Deflection Gages (Deflectometers) – Model 3540
Widely used for measuring deformations in three- and four-point bend tests, compression tests and a variety of general-purpose deflection measurements. These strain gaged devices come with a magnetic base for easy mounting.
38 EXTENSOMETER MODELS are available in many thousands of variations. Our focus on helping customers has led to the development of models to cover nearly any test method.
Operation of these extensometers are
VERIFIED TO EITHER ASTM E2309 OR ISO 9513 STANDARDS
using in-house calibration systems that are calibrated with Epsilon’s laser interferometer system.
WITH EPSILON’S 20+ YEAR HISTORY OF SERVICE
to the materials testing community, you know we will be there to stand behind our products when your critical application requires it.
Deflection is measured with a single arm with an attached spherical contact tip, similar to those on a dial indicator. The full bridge strain gaged construction provides an electrical output compatible with any electronics designed for a strain gaged transducer.
The magnetic mounting base supplied with the deflectometer can be mounted to the desired reference surface, whether flat or round, and the tip can be easily positioned to measure deformations during the test. The mounting system is designed to enable convenient swing in / swing out positioning of the deflectometer, when needed, without having to realign the deflectometer between tests.
All models feature a spring-loaded arm that can break free in the event of excessive displacement, protecting the deflection gage from damage. The upper arm exerts a small spring force against the specimen, which is sufficient to allow dynamic cyclic testing if desired, yet light enough in force to avoid influence on the test.
These units come standard with the arm set to measure downward deflections when oriented in the upright position. They can be used upside down or in any orientation. The measuring ranges listed are total displacement.
Model 3540 deflectometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller with electronics for a strain channel, and Epsilon will equip the deflectometer with a compatible connector that is wired to plug directly into the controller. For systems lacking the required electronics, Epsilon can provide a variety of signal conditioning solutions that enable connecting to data acquisition systems or other equipment.
- Full bridge, 350 ohm strain gaged design for compatibility with nearly any test system.
- General purpose deflection sensor covers many test requirements; may be used in any orientation.
- Comes with an adjustable magnetic base for easy mounting and convenient swing in / swing out positioning.
- Spring loaded arm detaches to prevent damage from overtravel.
- Meets ASTM and ISO accuracy classes as follows.
- -001M, -004M, -006M, -005T, -015T, -025T:
ASTM E2309 Class A
ISO 9513 Class 1
ASTM E83 Class B-2 (assuming 50 mm gauge length per D790 and D6272) - -012M, -025M, -050M, -050T, -100T, -200T:
ASTM E2309 Class B
ISO 9513 Class 2
ASTM E83 Class C (assuming 50 mm gauge length per D790 and D6272)
- -001M, -004M, -006M, -005T, -015T, -025T:
- All standard units have linearity of 0.25% of FS or better.
- Includes the Epsilon Shunt Calibration System for on-site electrical calibration.
- Rugged, dual flexure design for improved performance.
- Includes high quality foam lined case.
Excitation: 5 to 10 VDC recommended, 12 VDC or VAC max.
Output: 2 to 4 mV/V, nominal, depending on model
Linearity: ≤0.25% of full scale measuring range
Temperature Range: Standard (-ST) is -40 °C to +100 °C (-40 °F to 210°F)
Cable: Integral, ultra-flexible cable, 2.5 m (8 ft) standard
Operating Force: <1.5 N (0.3 lbf) typical
- Connectors to interface to nearly any brand of test equipment
- Model PH2040 magnetic mounting base – provides 6+ degrees of freedom adjusted with one knob; ideal when measuring deflections of assemblies and structures
-
4mm travel
-
25mm travel
-
Model 3540 release mechanism
-
Included magnetic mounting base
-
3-point and 4-point bending
-
Inverted measurement
-
Off-axis measurement
Product Videos
Deflectometer example applications: four-point bending, three-point bending, and component deflection in various orientations
Ordering Information
Click table options to configure
Measuring Range i
| mm or inches | # |
|---|---|
| 1.0 mm | -001M |
| 4.0 mm | -004M |
| 6.0 mm | -006M |
| 12.0 mm | -012M |
| 25.0 mm | -025M |
| 50.0 mm | -050M |
| 0.050 in | -005T |
| 0.150 in | -015T |
| 0.250 in | -025T |
| 0.500 in | -050T |
| 1.000 in | -100T |
| 2.000 in | -200T |
Temperature Range
| degrees | # |
|---|---|
| -270 ˚C to 100 ˚C (-454 ˚F to 210 ˚F) | -LT |
| -40 ˚C to 100 ˚C (-40 ˚F to 210 ˚F) | -ST |
| -40 ˚C to 150 ˚C (-40 ˚F to 300 ˚F)¹ | -HT1 |
| -40 ˚C to 200 ˚C (-40 ˚F to 400 ˚F)¹ | -HT2 |
| -270 ˚C to 200 ˚C (-454 ˚F to 400 ˚F)¹ | -LHT |
Model Number: 3540 – _ _ _ _ – _ _
Model Number:
3540 – _ _ _ _ – _ _
Model 3540 Available Versions: ANY combination of measuring range and temperature range listed above is available. Other configurations may be available with special order; please contact Epsilon to discuss your requirements.
¹Magnetic base not suitable for high temperature use; 50 °C (125 °F) max.
Example: 3540-012M-ST: 12.0 mm measuring range, standard temperature option (-40 °C to 100 °C)
Related Models
Repairs/Service
If your unit is in need of service, calibration or repair, initiate the RMA process with us and we will be happy to assist.
Get Our Newsletter
Sign up for our newsletter to get the most up-to-date information on products and services.
Download Catalog
Our 2022 Extensometer Catalog, Version 110 is now available! Not finding something you’re looking for? Ask us about a custom quote.
